Open the folder for any project sitting on your desk and ask a few awkward questions. Is there work in there from three years ago that you have never deleted, and cannot quite explain why you are keeping it? When someone asks for the latest drawing of a part, does the answer involve walking over to a colleague and asking whether a file is really the final version? If a batch of drawings had to go to an outside supplier tomorrow, could you promise that after compression every dimension and tolerance would still read cleanly?
If any of those made you hesitate, this is written for you. In manufacturing, the trouble with files is seldom that they will not fit. It is that nobody dares touch them. Nobody deletes, nobody recompresses, and nobody wants to be the one who sent a drawing out looking wrong.
UglyPear Data has spent years working on high-performance document compression and enterprise knowledge engineering, and the same scene turns up in factory after factory. A mid-sized mechanical plant holds hundreds of thousands of files on its servers: drawings, process sheets, inspection reports, change orders, layer upon layer. Perhaps one in ten gets opened regularly. The other nine sit untouched. Deleting them feels risky; keeping them eats space and slows every search. The pile grows until it becomes an inheritance nobody wants to claim.
Manufacturing files are not ordinary documents
An assembly drawing is dense with dimensions, tolerances and material notes, with lines as fine as a hair. Compress it too hard and the edges of the numbers start to soften. A tolerance written as plus or minus zero point zero five blurs into a smudge, and on the shop floor a smudge can turn into a scrapped part. Process documents carry embedded tables and charts. Scanned inspection reports carry handwritten signatures and red stamps. These are exactly the details that cannot be lost.
Versions are worse. A single part may go through a dozen revisions from design to production, and every revision has to be retained. That is both a traceability requirement and the evidence that protects you when something goes wrong. Keeping everything becomes the default, and no one volunteers to subtract.
Then there is format. Manufacturing data arrives from everywhere: drawings exported from design software, measurement data from coordinate machines, plant survey data, geolocation for equipment placement. General-purpose compression handles familiar images and PDFs well enough, but against these specialist formats it often stalls. Either it cannot reduce them at all, or the result will not open.
What keeps piling up is not just files
This is not one company's bad habit.
Komprise has reported that 74 percent of large organisations hold more than five petabytes of unstructured data, 40 percent more than ten, and that 85 percent of IT leaders expect storage spending to keep climbing. Manufacturing feels this sharply, because drawings and inspection imagery are naturally heavier than ordinary text.
What is striking is how much of it is inert. Another Komprise study found that 60 to 70 percent of data on enterprise storage had not been touched in over ninety days, yet it still occupied the most expensive tier. Why not clear it out? A nationwide survey by Compass Datacenters put a finger on the psychology: 77 percent of people admitted hoarding more data than they needed, and 42 percent held on to files because they might be useful later. In manufacturing that fear carries an extra weight. Deleting the wrong drawing is not a mistake anyone wants on their record.
So the inert data stacks up, the storage bill keeps climbing, and everyone can see the knot while nobody moves to untie it.
Space, though, is only the visible cost. The quieter one is time spent looking for things. A comparative study from the Knowledge Worker foundation put numbers on it: employees at organisations without a knowledge-management programme averaged 8.5 hours a week searching for information; with one, that dropped to 4.6 hours, a saving of 3.9 hours a week, equivalent to releasing 98 full-time roles per thousand employees. An engineer hunting for a drawing or a process sheet often moves between the file system, email and chat, then has to confirm whether the copy is current. None of that appears on a balance sheet, and all of it consumes people.
Compression and organisation chip away at this knot. Smaller, more searchable, easier-to-archive files move people out of the business of finding and waiting.
Even the awkward leftovers have a place to go
Compression capability has kept expanding outward. Some time ago the team brought less common professional formats into scope: geographic information, engineering survey data, laser point clouds. What does that change for a manufacturer?
Plant floor plans, production-line layouts and equipment-location survey data used to sit outside compression altogether. The files were huge, the formats unfamiliar, general tools would not touch them, so they were stored as-is. Now that kind of data can be brought under the same discipline and made lighter without losing the geometry that matters. Put plainly, the leftovers that a plant could neither compress nor dare to delete finally have somewhere to land.
Where you compress matters more than how
There is one more layer that cannot be brushed aside: intellectual property.
A manufacturer's drawings and process parameters are the core of the business. The IBM Cost of a Data Breach Report 2025 contains a detail worth pausing on. Customer personal information accounts for 53 percent of stolen data, while intellectual property accounts for 33 percent, yet each IP record ranks among the most expensive at roughly 178 dollars a piece. When a drawing leaks, the damage is rarely just a fine. It is a real loss of competitive ground.
That is why many manufacturers would rather compress locally and store on an internal network than upload to a public online tool. The moment a file leaves the building, control over its risk stops being yours. Compression looks unremarkable on the surface, but in manufacturing it becomes part of data governance. Where it happens, who performs it, and where the result lives all need an answer.
Choose on criteria before you choose a tool
So which route should a manufacturer take? Rather than arguing about a particular product, it helps to lay out the dimensions.
| Selection dimension | Local, on-device compression | General online or cloud-drive tool | Private compression with a knowledge base |
|---|---|---|---|
| Engineering and specialist formats | Common formats handled; specialist ones depend on the tool | Mostly common images and PDFs; limited specialist coverage | Can span multiple formats including engineering survey data |
| Does data leave the premises | Stays on the machine | Uploaded to the provider's servers | Kept inside the organisation's own network |
| Batch and version handling | Suited to scattered single files | Small batches; weaker at scale and retention | Directory-wide batches, versions can be retained |
| Intellectual property | Depends on local security | Rests on the provider's promises | Data sovereignty stays with the organisation |
| Search and reuse afterwards | Ends at compression | Usually no search | Can feed a knowledge base, find files by content |
| Best fit | One-off personal compression | Non-sensitive, single conversions | Cross-team work, drawing assets, high compliance needs |
These are qualitative, relative comparisons; coverage means the range of capability, not an absolute performance score.
No single route wins everywhere. Compressing one drawing for personal use does not need more than a local tool. But managing the drawing assets of an entire plant, issuing versions outward and searching inward, only works along the third path. The test is pleasantly simple. Can the file leave the building? After compression, does it still need to be found and used? Answer those two and the choice stops being difficult.
What counts as compressing well
One more thought. Many people measure success by how far the size dropped, and assume that more is better. Manufacturing is exactly where that instinct misleads.
The real questions are different. After compression, can a machine still read the dimension callouts? Open the file in another software, decades from now, and will it still display? On a scanned inspection report, are the signature and the stamp still verifiable? The line worth holding is not smallness. It is that key information stays complete, verifiable and recoverable. Size is a by-product.
Getting there means setting quantifiable acceptance criteria before touching anything: how accurately key fields are recognised, how readable the output remains, how well retrieval recalls what you need. Eyeballing a file and deciding it looks fine is not a standard. More disciplined practices run a set of reference samples through a regression pass on every adjustment, so nothing genuine gets compressed away along with the redundancy. There are boundaries to respect as well. A signed final revision, or an original kept as legal evidence, is better left untouched. Not every shop will adopt all of this, but the habit of fixing the acceptance criteria before starting is worth borrowing.
The paragraphs above describe practices and judgements common across the industry. What any given tool can actually do still needs testing against your own sample files; conclusions are not something to copy wholesale.
Where to start
SmartSlim takes the local route, with compression that keeps data on the computer and pays particular attention to preserving fine details such as drawing dimensions and stamps. It covers common types including PDF, images, Office files and engineering drawings, with versions for a wider set of formats. For a manufacturer whose files cannot leave the building but still need batch handling, this local-first approach fits well.
If the ambition goes beyond compression, towards turning drawings, process documents and inspection reports into something you can question and get answers from, look at the RAG data engineering foundation. It addresses a different problem: files get lighter first, then enter the knowledge base, all under private deployment, with sensitive information masked along the way. Compression here becomes a front-end step, so that the retrieval and question-answering downstream stay lighter and quicker.
Try it now
To see how local compression handles engineering drawings, explore SmartSlim. To plan compression together with a private knowledge base, see the RAG data engineering foundation. More practical writing on compression and data engineering lives in the technical blog.
FAQ
Q: Will compressing a drawing blur critical dimensions and tolerances?
A: It can, which is why moderation matters. Compression always has a cost; the question is whether that cost lands on redundancy or on content. Set acceptance criteria first: run a batch of reference drawings, check that key fields still read correctly both to a machine and to the eye, and only then process everything. Better to compress a little less than to cross the line where real information starts to degrade.
Q: Do a manufacturer's files have to go to the cloud to be compressed?
A: No. Compression can run entirely on a local machine or inside the corporate network, without the files leaving. For drawings and process parameters that carry intellectual property, local compression is often the safer choice: data sovereignty stays in-house, and there is no need to extend trust to a third-party platform.
Q: Should old drawings that are rarely opened be deleted or kept?
A: It depends on compliance needs and traceability. Anything that may serve as evidence or falls under a retention period should stay. What is genuinely obsolete can be archived with lossless or light compression to reduce its footprint rather than simply erased. In the Compass survey, many people held on to files precisely because they might be needed later. Compressing, archiving and labelling them clearly solves that anxiety better than agonising over deletion.
Q: Beyond familiar PDFs and images, can scanned drawings and survey data be compressed?
A: Many tools handle scans and common engineering drawings. Specialist formats such as geographic information or laser point clouds depend on the tool's coverage. The recent capability expansion brought these into scope, but confirm the specifics when selecting a tool rather than assuming every format is supported.
Q: How should a manufacturer weigh private deployment against an online tool?
A: It comes down to one question: can the file leave the building? Where drawings and process documents are sensitive assets, or where customers and regulators impose compliance requirements, favour something that runs inside your own network. IBM's report notes that IP records rank among the costliest when lost, which is a good reason for this kind of business to keep data close.